The Designer's Guide Community Forum
https://designers-guide.org/forum/YaBB.pl Simulators >> Circuit Simulators >> ADS to design and simulate antena( please, help me) https://designers-guide.org/forum/YaBB.pl?num=1273022317 Message started by hieuphong on May 4th, 2010, 6:18pm |
Title: ADS to design and simulate antena( please, help me) Post by hieuphong on May 4th, 2010, 6:18pm hi you! i'm using ADS ( advanced design system) to simulate RF circuit. now, i'm having a problem i need everyboy help me My problem is" circuit design set rotate phase, combine Hybrid ( 90 degree) and varactor diode to control phase angle shift between input and output" i have been designed it but i want to simulate by ADS with: " vatical axis is angle phase, horizontal axis is capacitance not frequency" please help me. |
Title: Re: ADS to design and simulate antena( please, help me) Post by pancho_hideboo on May 4th, 2010, 8:56pm I can't find out any design issue in your post. Your questios are no more than very easy usage of very specific tool. Do two AC or SP analyses. (1) AC with dc voltage sweep for varactor alone (2) AC or SP analysis with dc voltage sweep for phase shifter You can get capacitance from (1). You can get phase shift from (2). Here you can also do (1) in (2) by placing replica varactor for evaluation of capacitance. Then use "plot_vs()" function. http://edocs.soco.agilent.com/display/ads2009/plot+vs%28%29 Read all documents of Agilent ADS surely. The followings are general notes for you. - Always describe vendor's name which you use as tool or simulator. - Don't do multiple posts which are same content. - Don't request source code or behavioral model without any efforts. - There are many simulators which have analyses called as PSS, PAC and Pnoise. - Describe in detail with using correct terminologies. - Warnigns are different from Errors. - ADS is not name of simulator. - There is no tool which name is Cadence. - Don't use Direct Plot of Cadence ADE blindly without knowing definition. - All gains in Direct Plot of Cadence ADE are "right", "true" and "practical" voltage gain. - Don't mix up Simulation with Post Processing. They are completely different phase. - MATLAB are different from Simulink. - Learn measurements using actual instruments. Not "EDA Tool Play |
Title: Re: ADS to design and simulate antena( please, help me) Post by hieuphong on May 5th, 2010, 4:31am hi pancho. i sent to you my design file. Please check it. Now i want to use a voltage to control varactor diode why i have to do. Mybe when you see my file, You will understand. |
Title: Re: ADS to design and simulate antena( please, help me) Post by pancho_hideboo on May 5th, 2010, 4:41am It seems you are not familiar with Agilent ADS. So it seems you can't understand my answers at all. What you want to do is very easy task in Agilent ADS. |
Title: Re: ADS to design and simulate antena( please, help me) Post by hieuphong on May 5th, 2010, 12:51pm it's an ADS 2008 update 2. Do you understand my question? Maybe, my english is too bad so you don't know what i wrote OK. i repeat my problem " i want to design a circuit that combine between quadrature hybrid and vacator diode. to use diode to control angle phase shift between input and output.the ange phase shift will change [0:360 degree] when vacator diode change capacitance." Now i want to simulate by ADS. vatical axis is angle phase shift, horizontal axis is capacitance" You can see figure |
Title: Re: ADS to design and simulate antena( please, help me) Post by pancho_hideboo on May 6th, 2010, 2:12am Don't attach such non-valuable figure. hieuphong wrote on May 5th, 2010, 12:51pm:
Answer is http://www.designers-guide.org/Forum/YaBB.pl?num=1273022317/1#1 Again, what you want to do is very easy task in Agilent ADS. This is a special service since you are new comer in this forum. Maybe you are student. So discuss such very easy issue with friends or read all documents surely next time. |
Title: Re: ADS to design and simulate antena( please, help me) Post by pancho_hideboo on May 6th, 2010, 2:19am hieuphong wrote on May 4th, 2010, 6:18pm:
hieuphong wrote on May 5th, 2010, 4:31am:
hieuphong wrote on May 5th, 2010, 12:51pm:
No varactor or voltage-controlled-capacitor is used in any of "FULL_TK2_020_e343(2).dsn", "hic.dsn" and "thunghiem.dsn". Maybe you substitute fixed value "CAPQ" for "varactor". So situation is more easy than "http://www.designers-guide.org/Forum/YaBB.pl?num=1273022317/1#1". |
Title: Re: ADS to design and simulate antena( please, help me) Post by pancho_hideboo on May 6th, 2010, 2:30am Again, what you want to do is very easy task in Agilent ADS. Again read all documents of Agilent ADS surely. Attached archive include schematic("*.dsn", "*.ael", "*.atf") and "*.dds" files I used. |
Title: Re: ADS to design and simulate antena( please, help me) Post by hieuphong on May 6th, 2010, 1:32pm thanks for your help, pancho. I have done my lesson,again. I'm a student in VietNam, the firt time i have used ADS to simulate and design RF circuit,Microwave. i hope, i will help more and more Good luck to you, Pancho. |
The Designer's Guide Community Forum » Powered by YaBB 2.2.2! YaBB © 2000-2008. All Rights Reserved. |