The Designer's Guide Community Forum
https://designers-guide.org/forum/YaBB.pl Design Languages >> Verilog-AMS >> Verilog-A to C compiler https://designers-guide.org/forum/YaBB.pl?num=1277409274 Message started by Ravi Ganti on Jun 24th, 2010, 12:54pm |
Title: Verilog-A to C compiler Post by Ravi Ganti on Jun 24th, 2010, 12:54pm Hi I am looking for a Verilog-A to C compiler. The functionality i desire to achieve is to simulate the Verilog-A code using Spectre and generate I-V curves and do the same by converting Verilog-A into C code and then by using HSPICE generate I-V curves. Then i wanted to compare both of them. Any help in this regard is greatly appreciated. Thanks in advance. Ravi Ganti |
Title: Re: Verilog-A to C compiler Post by patrick on Jun 24th, 2010, 1:07pm Hi Ravi, HSPICE supports Verilog-A since 2005.03 Patrick |
Title: Re: Verilog-A to C compiler Post by Ravi Ganti on Jun 28th, 2010, 5:00pm Hi Patrick, I actually want to run Verilog-a code using NGSPICE which is an open source version of SPICE. In this regard i was planning to convert Verilog-a into C and then use this C code to run in NGSPICE. In this regard i am looking for Verilog-a to C compiler. I am new to both NGSPICE and also Verilog-a but took this project as an academic project. Your help in this regard is highly appreciated. Thanks Ravi Ganti |
Title: Re: Verilog-A to C compiler Post by patrick on Jun 28th, 2010, 5:39pm Use ADMS, see: http://ngspice.sourceforge.net/adms.html |
Title: Re: Verilog-A to C compiler Post by Ravi Ganti on Jun 30th, 2010, 4:17pm Hi Patrick, Thanks for the link. The information proved very useful. I have some issues when i try to install ADMS source code. I was wondering if you can help me with it. The following is the error message which i am getting while trying to install ADMS: This message showed up on my terminal when i tried ./configure checking whether to enable maintainer-specific portions of Makefiles... no checking for g++... no checking for c++... no checking for gpp... no checking for aCC... no checking for CC... no checking for cxx... no checking for cc++... no checking for cl.exe... no checking for FCC... no checking for KCC... no checking for RCC... no checking for xlC_r... no checking for xlC... no checking whether the C++ compiler works... no configure: error: in `/home/ganti/Desktop/Summer_Project/Compiler related/adms-2.2.9': configure: error: C++ compiler cannot create executables See `config.log' for more details. Thanks Ravi Ganti |
Title: Re: Verilog-A to C compiler Post by Ravi Ganti on Jun 30th, 2010, 5:09pm I just recognized that i did not have g++ installed which is one reason why i might be getting that error. I am checking for other missing programs, which could have caused my ./configure to stop. Thanks Ravi Ganti |
Title: Re: Verilog-A to C compiler Post by Geoffrey_Coram on Jul 1st, 2010, 5:44am Ravi Ganti wrote on Jun 30th, 2010, 4:17pm:
The SourceForge site is a better place to get help for ADMS; there's a contact e-mail for the developer (Laurent Lemaitre). |
Title: Re: Verilog-A to C compiler Post by Ravi Ganti on Jul 1st, 2010, 10:59am Thanks, for extended support. Best Ravi Ganti |
The Designer's Guide Community Forum » Powered by YaBB 2.2.2! YaBB © 2000-2008. All Rights Reserved. |