Designer’s Guide Community

haykp Community Member Offline Posts: 40	Vdd tied to ground in AC mode Oct 21^st, 2011, 12:12am Dear Forum, As you know while doing small-signal analyses (AC) we consider the VDD tied to ground. Please help me understand why? thanks,
Back to top	IP Logged

buddypoor Community Fellow Offline Posts: 529 Bremen, Germany	Re: Vdd tied to ground in AC mode Reply #1 - Oct 21^st, 2011, 12:35am haykp wrote on Oct 21^st, 2011, 12:12am: Dear Forum, As you know while doing small-signal analyses (AC) we consider the VDD tied to ground. Please help me understand why? thanks, VDD is considered as an ideal voltage source having an internal source resistance of zero. Thus, ac-wise it is grounded.
Back to top	LvW (buddypoor: In memory of the great late Buddy Rich) IP Logged

loose-electron Senior Fellow Offline Best Design Tool = Capable Designers Posts: 1638 San Diego California	Re: Vdd tied to ground in AC mode Reply #2 - Oct 21^st, 2011, 5:53am What is the value of AC signals present in a DC bias line? Answer = Zero
Back to top	Jerry Twomey www.effectiveelectrons.com Read My Electronic Design Column Here Contract IC-PCB-System Design - Analog, Mixed Signal, RF & Medical IP Logged

buddypoor Community Fellow Offline Posts: 529 Bremen, Germany	Re: Vdd tied to ground in AC mode Reply #3 - Oct 21^st, 2011, 6:18am loose-electron wrote on Oct 21^st, 2011, 5:53am: What is the value of AC �signals present in a DC bias line? Answer = Zero What do you mean with "signal"? I think the dc line can carry an ac current, can it not?
Back to top	LvW (buddypoor: In memory of the great late Buddy Rich) IP Logged

Garrett.Neaves

Junior Member

Offline

Analog Design
Engineer

Posts: 18
United States

Re: Vdd tied to ground in AC mode
Reply #4 - Oct 21^st, 2011, 6:54am

haykp wrote on Oct 21^st, 2011, 12:12am:

Dear Forum,

As you know while doing small-signal analyses (AC) we consider the VDD tied to ground.
Please help me understand why?

thanks,

You set vdd to ac ground when you are doing an ac analysis in which your ac input signal is some signal other than vdd.

Typically, an ac analysis is concerned with the ac response due to a single ac signal source. �That is, all ac signal sources are set to zero except for the one of interest.

If the ac response to the ac component of vdd is of interest, then vdd would not be tied to ground. �Instead, all other ac signal sources would be set to zero. �The ac response due to signal on a power supply such as vdd is generally referred to as PSRR for power supply rejection ratio or power supply ripple rejection.

Back to top

IP Logged

buddypoor Community Fellow Offline Posts: 529 Bremen, Germany	Re: Vdd tied to ground in AC mode Reply #5 - Oct 21^st, 2011, 6:58am I am afraid, there is a misunderstanding. For my opinion the content of the original question is: Why is the source Vdd replaced by signal ground during ac analysis?
Back to top	LvW (buddypoor: In memory of the great late Buddy Rich) IP Logged

haykp

Community Member

Offline

Posts: 40

Re: Vdd tied to ground in AC mode
Reply #6 - Oct 21^st, 2011, 7:15am

Thanks all for the comments!

buddypoor many thanks for your more precise explanation.
But one question regarding yourcomment: if the internal source resistance is zero, does it mean we can tied it to ground?

Will you agree with following proof:
In ac mode there is cap between Vdd and Vss, hence we can assume that Vdd is tied to ground.

Back to top

IP Logged

raja.cedt

Senior Fellow

Offline

Posts: 1516
Germany

Re: Vdd tied to ground in AC mode
Reply #7 - Oct 21^st, 2011, 7:34am

hello haykp,

Let me explain what is small signal to understand this bit clearly.

Small signal means how your ckt parameters are changing with applied signal(don't confuse with the ac or dc, it's just change in the bias forget about the frequency for now ). So for example take a transistor with 100uA bias current for .5v vgs, now if you change vgs by 1mv then your current changes by 10uA, so in small signal model we only represent changes (not fixed quantities), now if you draw small signal model vgs and ids would be 1mV and 10uA. Think about an ideal voltage source, no change in the voltage hence short ckt, if it has some internal resistance, instead of short ckt, add resister from that node to gnd and same applicable to current source.

NOW Coming to your last post, we generally keep big decap between supply and gnd to support large amounts of switching currents. This acts as ideal voltage source, so you can represent it by short ckt.

SORRY FOR THE BIG POST.

Thanks,
raj.

Back to top

IP Logged

raja.cedt Senior Fellow Offline Posts: 1516 Germany	Re: Vdd tied to ground in AC mode Reply #8 - Oct 21^st, 2011, 7:38am hey haykp, forgot to tell you, please understand small signal model is not ac, where as small signal model will be used to do ac analysis. Thanks, raj.
Back to top	IP Logged

buddypoor Community Fellow Offline Posts: 529 Bremen, Germany	Re: Vdd tied to ground in AC mode Reply #9 - Oct 21^st, 2011, 9:05am In addition to Raja's explanations: In reality, the supply voltages are NOT ideal (with zero internal resistance) - and, therefore, we put a large capacitor across it (sometimes in parallel with a small one). This ensures a small and negligible internal ac resistance.
Back to top	LvW (buddypoor: In memory of the great late Buddy Rich) IP Logged

loose-electron

Senior Fellow

Offline

Best Design Tool =
Capable Designers

Posts: 1638
San Diego California

Re: Vdd tied to ground in AC mode
Reply #10 - Oct 21^st, 2011, 6:50pm

buddypoor wrote on Oct 21^st, 2011, 6:18am:

loose-electron wrote on Oct 21^st, 2011, 5:53am:

What is the value of AC �signals present in a DC bias line?
Answer = Zero

What do you mean with "signal"?
I think the dc line can carry an ac current, can it not? �

Agreed, however now you are analyzing the power supply loads, which probably is not what you want in a signal processing analysis.

Back to top

Jerry Twomey
www.effectiveelectrons.com
Read My Electronic Design Column Here
Contract IC-PCB-System Design - Analog, Mixed Signal, RF & Medical

IP Logged

haykp Community Member Offline Posts: 40	Re: Vdd tied to ground in AC mode Reply #11 - Oct 21^st, 2011, 11:32pm Dear raja.cedit and buddypoor, Many thanks for your explanations. Finally I understood he reason of replacing Vdd signal by ground in small signal analyses. Raj, yes I was mixing small signal analyze with AC analyze but now, after your comments I wont ) Thanks again.
Back to top	IP Logged

buddypoor

Community Fellow

Offline

Posts: 529
Bremen, Germany

Re: Vdd tied to ground in AC mode
Reply #12 - Oct 22^nd, 2011, 1:18am

haykp wrote on Oct 21^st, 2011, 11:32pm:

Raj, yes I was mixing small signal analyze with AC analyze but now, after your comments I wont

)

Hi Haykp, just for a correct understanding:
An ac analysis ALWAYS is a small-signal analysis. That means: All transfer characteristics are linearized around the chosen operating point (determined through bias conditions).

Back to top

LvW (buddypoor: In memory of the great late Buddy Rich)

IP Logged

haykp

Community Member

Offline

Posts: 40

Re: Vdd tied to ground in AC mode
Reply #13 - Oct 23^rd, 2011, 10:34am

Thanks buddypoor,

As we are speaking about AC analyze, at this stage my assumption is that there is some difference between AC analyze and small-signal analyze.
Though I understand that AC analyze uses small-signal analyze for calculations, but it somehow different. So what is the difference between AC analyze and small-signal analyze?
( please sorry if I am mixing anything)

Back to top

IP Logged

loose-electron

Senior Fellow

Offline

Best Design Tool =
Capable Designers

Posts: 1638
San Diego California

Re: Vdd tied to ground in AC mode
Reply #14 - Oct 23^rd, 2011, 7:33pm

AC analysis tends to mean looking at the frequency response of a system.
Small signal tends to mean looking at the signal processing characterisitics while ignoring DC bias issues.

That is not precise, but the term AC analysis comes from simulator origins, and small signal term comes from hand analysis methods.

thats the history of it...

They overlap and are somewhat similar.

Back to top

Jerry Twomey
www.effectiveelectrons.com
Read My Electronic Design Column Here
Contract IC-PCB-System Design - Analog, Mixed Signal, RF & Medical

IP Logged